- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Mapei Foamjet T is an ultra rapid setting and two-component polyurethane resin to be injected for waterproofing of structures subject to strong water ingress.
- Waterproofing rock or loose ground diggings, dams, shafts or tunnels where there is strong water ingress
- Waterproofing diaphragm and pile walls even when subject to constant contact with water
- For professional use only
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Quick Links - Click To Jump To Section:
Features & Benefits
- Uses:
- Waterproofing tunnels subject to high pressure water ingress through possible cracks or in fissures between keystones
- Waterproofing shafts or hydraulic structures with high pressure water ingress through working joints or cracks
- Repairing cracks in dams, channels and bulkheads when permanently immersed in water
- Sealing cracks in floorings or slabs that are damp or saturated with water
- Two-component polyurethane, halogene free resin, having very high reactivity and excellent mechanical performance and chemical stability
- Forms a polyurethane foam of great strength
- Due to its rheological properties, Foamjet T can also penetrate through small cracks and sealing them even if they are subject to water infiltrations
- At the end of the setting time, within a few seconds, depending on the temperature, Foamjet T becomes completely waterproof and ensures an adequate consolidation to the treated structure
- Meets the requirements defined by EN 1504-9 (“Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and evaluation of conformity. General principles for the use of products”) and the minimum requirements claimed by EN 1504-5: U(S1)W(3)(1/2/3/4)(5/35) (“concrete injection”)
Application
- Sealing cracks by injection:
- Positioning the injectors Make off-set holes on the sides of the cracks
- The size of the holes should fit the diameter of the injectors that will be used
- Expansion injectors with a non-return valve can be easily fixed by self-tapping completely to the walls of the hole
- If there is no water ingress, normal copper, steel or PVC tubes with a diameter of approximately 10 mm can be used
- The two components that make up Foamjet T must be mixed together by a special pump for two-component resins
- In order to carry out injection, Foamjet T part A and Foamjet T part B in the ratio 1:1 by volume, must be separately conveyed through the pump and into the nozzle previously placed on the injector and mixed by a helicoidal mixer placed within the nozzle. After mixing, Foamjet T must be injected continuously through the crack
- When the two components are mixed, the viscosity of the mixture increases substantially, therefore the injected mixture will not separate or be washed out by the water pressure. The increase in volume of the foam and its fast reaction stops the water ingress within a few minutes. In the absence of water, Foamjet T hardens without increasing in volume and rapidly seals the crack. NOTE: components A and B must be mixed thoroughly before use in order to blend in any additives that may have settled. Component A may become more viscous if stored at low temperatures
- Clean injection equipment (pump and tubes) with mineral oil, free of water and impurities after use.
- The consumption of the product depends on the size of the void volume to be filled and the foam expansion factor after mixing the two components, in relation to the amount of water present
- PACKAGING 44 kg units: – part A = 20 kg; – part B = 24 kg
Limitations
- Foamjet T is particularly recommended for waterproofing large areas where there is water ingress, also under pressure
- Foamjet T part A might be affected by a significant viscosity increase, when stored at low temperature
- Temperature influences the hardening time of Foamjet T; temperatures lower than +15°C lengthen setting time
- It is therefore recommended to seek information from our technical service before injection takes place in structures that are subject to high pressure water ingress
Data sheet
- Manufacturer
- Mapei
- For Use By
- Professional Use
- Interior / Exterior Use
- Interior & Exterior
- Application Method
- Injection
- Density
- Part A: 1.034 ± 0.026
Part B: 1.22 ± 0.04 - Shelf Life (from date of manufacture)
- 1 year
- Viscosity
- Part A: 471 ± 94
Part B: 322 ± 64 - Manufacturer
- Mapei
- Usages
- Waterproofing
- Product Usage Type
- Sealer
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Mapei Foamjet T is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT