- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Mapei Mapethene EQ is a self-adhesive bituminous membrane made from a mixture of bitumen and special polymers bonded to a film of high density polyethylene (HDPE), for waterproofing structures below ground level.
- With Vulc selvedge strip
- used to waterproof vertical and horizontal surfaces, foundation slabs, foundations, under ground garages and cellar walls. As well as all known and suitable mineral substrates.
For professional use only.
Mapethene EQ is a self-adhesive preformed bituminous waterproofing membrane made from a special mixture of bitumen admixed with polymers bonded to a film of HDPE, forming an impermeable sheet resistant to tearing.
Once applied Mapethene EQ is immediately resistant to water, including sudden rainfall. Mapethene EQ does not contain solvents. Mapethene EQ meets the requirements of EN 13969 (“Bituminous membranes to prevent rising damp from the ground”).
Quick Links - Click To Jump To Section:
Features & Benefits
- Self-adhesive bituminous membrane made from a mixture of bitumen and special polymers bonded to a film of high density polyethylene (HDPE)
- Used to waterproof vertical and horizontal surfaces, foundation slabs, foundations, under ground garages and cellar walls. As well as all known and suitable mineral substrates
- Applied cold in complete safety without using flames
- Highly flexible which makes it simple, quick and easy to apply
- Adheres perfectly to substrates. Thanks to the use of Mapethene Primer W wit may be applied at low temperatures and on slightly damp substrates. • Good crack-bridging properties once applied
- Impermeable up to a pressure of 4 bar
- Preformed membrane: more control on its thickness during production and complete uniformity of the mix
- 50 mm vulcanisation selvedge strip for secure adhesion of seams
- Waterproofing structures permanently against ground damp (capillary water, retained water), non-standing seepage water, pressure free water and as a water retardant under screeds
- Solvent free and environmentally friendly, applicable all year round
- Immediate resistance to water and driving rain.
- Meets the requirements of EN 13969 (“Bituminous membranes to prevent rising damp from the ground”)
Preparation
- Mapethene EQ may be applied on concrete, solid bricks and vibro-compressed concrete blocks
- Substrates must be flat, sound and clean. Remove cement laitance, loose and crumbling parts and traces of dust, grease and form release agents with a pressure washer and wait until all the water has dried off
- Remove all traces of old waterproofing material. If the reinforced cement structure to be waterproofed has gravel clusters or other irregularities, remove them with hand or power tools or by hydro-demolition
- Carefully clean any exposed rebar, treat them with a coat of Mapefer 1K anti-corrosion cementitious mortar and then fill all the gaps and demolished areas with Planitop Smooth & Repair R4 quick-setting, compensatedshrinkage, thixotropic cementitious structural mortar or a suitable product from the Mapegrout line of mortars
- When applying the product on bricks or blocks, on the other hand, completely remove all traces of mortar protruding from between the blocks, skim over any areas with defects and grout any gaps in the joints with Mapegrout 430 fine-textured thixotropic mortar or MapeWall Render & Strengthen high strength, natural hydraulic lime-based rendering and masonry mortar. Blend in all the corners between the foundations and walls and between adjacent vertical walls with the same products used to repair the surfaces and round off any sharp edges or corners
- Seal structural joints with Mapeband TPE tape bonded to the substrate with Adesilex PG4 epoxy adhesive broadcast with Quartz 0.5
- After preparing the substrate as specified, apply a coat of Mapethene Primer one-component, solvent-free bitumen emulsion. As an alternative at low temperatures, it is possible to use Mapethene Primer W one-component, ready-mixed primer
Application
- Seal any elements passing through horizontal and vertical surfaces with two pieces of Mapethene EQ cut to shape to form a collar between the object passing through the surface and the substrate
- When applying the membrane on horizontal surfaces, remove the first 20 cm of silicone film, line up the roll in the direction it is to be applied and unroll the Mapethene EQ. Remove the film as you unroll the membrane so that it adheres evenly to the substrate
- Overlaps between adjacent rolls of membrane must be at least 5 cm wide. Line up the membrane on the HDPE film of the roll of membrane already applied and bond the next roll of membrane. Make sure the joints between the pieces of membrane are staggered and then go over the overlaps carefully with a rubber roller
- When applying the membrane on vertical surfaces, we recommend cutting Mapethene EQ according to the height of the surface to be waterproofed. Remove around 30 cm of silicone film, line up the sheet according to the direction it is to be applied and bond it to the substrate starting from the highest point. Then apply the Mapethene EQ, making sure there is an overlap at least 5 cm wide, as described in the procedure for applying on horizontal surfaces
- To prevent damaging the upper edge of the membrane, we suggest applying Mapeband SA self-adhesive butyl tape with alkali-resistant, non-woven fabric backing, between the Mapethene EQ and the substrate
- Carry out localised repairs to areas that have been accidentally damaged with pieces of Mapethene EQ cut to suit from the roll of membrane
- Within 48 hours of applying Mapethene EQ, protect all waterproofed surfaces with a protective drainage membrane, such as Polyfond Kit Drain made by Polyglass S.p.A., which protects the Mapethene EQ when holes and trenches are filled in
- Clean hands with lukewarm water and tools with water or thinners
- Do not use Mapethene EQ in the following cases:
- During rainy weather
- On substrates with condensation or free-standing water on the surface
- Without a protective layer if exposed to direct mechanical loads
Data sheet
- Manufacturer
- Mapei
- For Use By
- Professional Use
- For Use On
- Concrete, bricks, underground structures
- Single, Two or Three Pack
- Single
- Pack Size
- 1m x 20m roll
- Max. Application Temperature
- 30°C
- Min. Application Temperature
- -5°C
- Shelf Life (from date of manufacture)
- 12 months
- Base Type
- Solvent-Free
- Suitable For Use On
- Concrete
- Suitable For Use On
- Brick
- Manufacturer
- Mapei
- Product Usage Type
- Membrane
- Product Range
- Mapethane
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Mapei Mapethene EQ is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT