- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Three-component, high-strength, rapid-hardening epoxy grout specifically developed for anchoring, repairing and grouting structures, including those subjected to dynamic loads and vibrations. Application examples include:
- Anchoring and grouting support bases for presses, compressors and heavy industrial machinery in general, including those subjected to high levels of mechanical stress
- Fastening and repairing rails for cranes, bridge cranes, tramway and rail tracks
- Levelling off the surface of bearing elements used to support floor beams
- Anchoring structural tie-rods, bolts and metal rods, including in areas subjected to vibrations and aggressive chemicals
- 96.1KG kit (component A = 10.5 kg; component B = 1.6 kg; component C = 84 kg (4 bags weighing 21 kg each))
- For professional use only
This item has a lead time of 4-6 weeks; please contact our sales team to make an order on 0113 2455450 or send a message to [email protected]
A three-component mortar made from epoxy resin and selected aggregates in a granulometric curve. The innovative Low Dust technology that characterises this product considerably reduces the amount of dust given off during mixing compared with conventional cementitious-based products, thereby helping to make work easier and safer.
Quick Links - Click To Jump To Section:
Features & Benefits
- After mixing Planigrout 310 component A with its relative catalyser (component B) and fillers (component C), it forms a free-flowing, solvent-free mortar with the capacity to flow into tight areas. The product is applied in layers from 2.5 cm to 10 cm thick
- After mixing, Planigrout 310 hardens by means of a chemical curing process and forms a compound characterised by its excellent adhesion and resistance to chemicals, as well as a high level of strength within just a few hours of application
- The mortar’s rapid hardening properties allow industrial machinery and equipment to be put into service very quickly and help reduce down times
- Main characteristics of hardened Planigrout 310 may be summarised as follows:
- Impermeable to water and oil
- High resistivity
- Resistant to attack from chemicals
- High mechanical performance properties
- Resistant to vibrations
- Resistant to freeze/thaw cycles
- Excellent adhesion to concrete and steel
- Rapid polymerisation
- Easy to apply thanks to is highly fluid consistency
- Planigrout 310 remains workable for around 30 minutes at +23°C and may be applied at temperatures of 10°C to 35°C
- The product is slightly more viscous and less fluid at lower temperatures, whereas at higher temperatures the workability time of Planigrout 310 is considerably lower. When applying the product in particularly cold or hot weather it will need to be cooled down or warmed up to around +23°C (in a temperature-controlled container for example) prior to application
- If the surrounding temperature and, therefore, the temperature of the substrate are less than +10°C, apart from warming the product as described above, it is necessary to apply the product in confined areas that have been warmed up to create suitable application conditions
- Planigrout 310 meets all the main requirements for EN 1504-9 (“Products and systems for the protection and repair of concrete structures; definitions, requirements, quality control and evaluation of conformity. General principles for use of products and systems”) and the minimum requirements for EN 1504-6 (“Anchoring of reinforcing steel bar”).
Recommendations & Limitations
- Do not use Planigrout 310 to seal elastic joints or joints subject to movement (use products from the Mapesil or Mapeflex range)
- Do not use Planigrout 310 to fill or repair areas less than 2.5 cm or more than 10 cm thick
- Do not use Planigrout 310 for construction joints between old and fresh concrete (use Eporip)
- Do not apply Planigrout 310 on wet surfaces
- Do not apply Planigrout 310 on dirty or crumbling surfaces
- Do not leave packs of Planigrout 310 exposed to direct sunlight prior to use
- Do not use Planigrout 310 if the temperature is lower than 10°C or higher than 35°C
Application & Preparation
Please refer to the data sheets in the tab above for further information.
Data sheet
- Manufacturer
- Mapei
- For Use By
- Professional Use
- For Use On
- Concrete
Industrial Floors
Workshop Floors
Machinery Bases - Single, Two or Three Pack
- Three-Pack
- Pack Size
- 96.1KG
- Minimum Applied Thickness
- 2.5cm
- Maximum Applied Thickness
- 10cm
- Coverage
- Approximately 2.20 kg/l of cavities to be filled.
- Max. Application Temperature
- 35°C
- Min. Application Temperature
- 10°C
- UN Number
- UN3082
- UN Number
- UN2259
- Pot Life
- approx. 30 mins.
- Suitable For Use On
- Concrete
- Suitable For Use On
- Workshop Floor
- Suitable For Use On
- Machinery
- Suitable For Use On
- Industrial Floors
- Manufacturer
- Mapei
- Usages
- Rapid Hardening
- Product Usage Type
- Grout
- Product Range
- Planigrout
- Setting Time
- 4 hours
- Hardening
- 7 days
- Colour Family
- Grey
- Colour Family
- Yellow
- Colour Family
- Off White
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Mapei Planigrout 310 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT