- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
An adhesive for chemically anchoring metal bars in holes made in building materials, specifically formulated for anchoring zinc- plated threaded and deformed steel bars which transmit structural loads in solid and perforated substrates such as non-cracked concrete, lightweight concrete, stone, wood, bricks and mixed masonry.
- Specific also for anchoring metal bars in tension and compression zones in cracked and non-cracked concrete, including in areas at risk of seismic activity
- Also an ideal solution for anchoring close to edges or when there is a limited space between each anchor, as no stress generated as with conventional mechanical expansion fasteners
- Recommended for anchoring elements in place, such as:
- Strengthening rods in construction joints
- Immersed anchors and anchors in damp environments
- Anchors in marine and industrial environments
- Overhead crane and tram rails
- Plant and sanitary equipment
- Aerials and signs, pylons, safety barriers
- For professional use only
Recommended for immersed anchors which are permanently damp, in marine and industrial environments subjected to chemical aggression, areas where the temperature is as low as -10°C when the product is applied and for anchors with a horizontal, vertical, inclined or overhead axis; it may also be used on substrates which are damp or wet at the moment of application where there are high static or dynamic stresses.
Quick Links - Click To Jump To Section:
Features & Benefits
- A two-component chemical anchoring product
- Packaged in 300 and 420 ml cartridges with two separate compartments containing component A (resin) and component B (catalyser), at the correct mixing ratio in volume
- The two components are mixed together when they are extruded via the static mixer supplied with the cartridge
- The mixer is screwed to the end of the cartridge, and no preliminary mixing of the two components is required
- If only part of the cartridge is used, the remaining product may be used, even after a number of days, by replacing the original static mixer clogged by hardened resin with a clean, new one
- Does not contain styrene which makes it suitable for use in areas with poor ventilation and, due to its low shrinkage, it is also suitable for anchors with small circular crests
- A chemical anchor made from a mixture of styrene-free resins, suitable for application on a wide range of solid and perforated building materials, such as:
- Non-cracked concrete
- Lightweight concrete
- Cellular concrete
- Masonry
- Bricks
- Stone
- Wood
- Applied in holes made with a drill or hammer drill. Mapei recommend using only a drill on perforated substrates
- Certified according to ETA European Standards option 1 (anchors in concrete in tension or compression zones), ETA rebar (supplementary reinforcement) and fire certification, ETA seismic performance C1 (in seismic zones)
- 300ml size cartridges may be used with conventional silicone extrusion guns for 50mm diameter cartridges, as long as they are robust enough. The 420 ml cartridges need to be used with a special extrusion gun for 65mm diameter cartridges
Recommendations & Limitations
- Do not apply on dusty or crumbling surfaces
- For use on damp or wet substrates, please contact Mapei or Rawlins Technical department on 0113 2455450 (option 2) or send a message to [email protected]
- Do not use on surfaces with traces of oil, grease and stripping compounds otherwise it will impede or reduce adhesion
- Do not apply if the temperature is lower than -10°C
- If used on natural stone, check if it impregnates into the stone
- Do not apply loads until it has completely hardened (see table 1 in data sheet)
- Do not use the product in holes made with a diamond-tipped bit (cored holes): use Mapefix EP 385
Application & Preparation
Please refer to the data sheets in the tab above for further information.
Data sheet
- Manufacturer
- Mapei
- For Use By
- Professional Use
- For Use On
- Concrete
- Single, Two or Three Pack
- Single
- Pack Size
- 300ml
420ml - Coverage
- According to the size of hole to be filled (see tables 11 and 12)
- Max. Application Temperature
- 35°C
- Min. Application Temperature
- 10°C
- Suitable For Use On
- Concrete
- Manufacturer
- Mapei
- Product Usage Type
- Adhesive
- Product Range
- Mapefix
- Colour Family
- Grey
- Categorised As
- Repairs > Low Temperature Bonding and Adhesives
- Seasonal
- Cold Weather
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Mapei Mapefix VE SF is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT